Amprobe Multitest-1000 Continuity-Tester Instrukcja Użytkownika Strona 23
- Strona / 122
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4.2.1.2. Mode "TIMER"
6. Use the following keys to set the duration time of the test:
Press this key to increase the duration time of the test (Tmax=999 seconds).
Press this key to decrease the duration time of the test (Tmin=10 seconds).
7. Press the START/STOP key.
START
STOP
The instrument completes the measurement when the set time has elapsed.
999 seconds → Maximum value of the test duration.
10 seconds → Minimum value of the test duration.
Note:
Pressing the START/STOP key again the test gets immediately interrupted.
)
R
ISO
.
07 MΩ
500 V 20
s
TIMER
At the end of the test, in case the
resistance value R
ISO
detected is
lower than R
MAX
(depending on the
selected voltage see following table) and
the test is performed at the selected
rated voltage value, the instrument
emits a double beep indicating the
positive outcome of the test displays
one screen similar to the screen
alongside.
Insulation
resistance value
R
ISO.
Rated voltage value selected for the Timer test.
SAVING
: The test can be stored pressing the SAVE key twice (refer to
paragraph 5.1).
Note
: The maximum resistance value R
MAX
that can be measured in mode MΩ depends
on the rated voltage selected for the test. In particular:
Rated voltage selected
for the test
R
MAX
= Maximum resistance
value
50VDC
99.9MΩ
100VDC
199.9MΩ
250VDC
499MΩ
500VDC
999MΩ
1000VDC
1999MΩ
Timer mode.
Duration of the
test.
SAVE
- MultiTest 1000 1
- 2. GENERAL DESCRIPTION 6
- ) SAVE key to save tests 8
- 3. PREPARATION FOR USE 9
- WARNING 12
- LOWΩ 13
- ν> 5 14
- 219 mA 16
- MEASURED 17
- CALIBRATION 17
- B2 B3 B4B1 20
- 500 V 20 22
- 999 MΩ 25
- 388V 388V 27
- 29
- 0 V 388 30
- 0 V 0 V 30
- 2P 32
- 2 40
- >1999 Ω 42
- 8. MAINTENANCE 49
- 9. TECHNICAL SPECIFICATIONS 50
- Code Description Code 53
- 10. SERVICE 54
- EQUALIZING POTENTIAL NODE 58
- TEST LEADS 58
- Bl a c k 62
- 2° Measurement: 64
- MULTITEST1000 69
- 2. DESCRIPCIÓN GENERAL 72
- 3. PREPARACIÓN PARA EL USO 74
- 219 mA 5 s 80
- 216mA 5s 81
- T2 T3 T4T1 83
- 500 V 20 s 85
- 500 V 20s 86
- ISO en función de la tensión 86
- >999 MΩ 87
- 500 V 20 s 87
- 2P 0.93 Ω 93
- 2P 0.93 Ω 96
- 2 0.93 Ω 99
- - - - c 100
- --- 100
- 3- - - m 101
- EN MEMORIA 102
- ATENCIÓN 104
- ESTÁNDAR 105
- 8. MANTENIMIENTO 107
- –0% +10% 108
- - Medida de resistividad ρ 109
- 10. ASISTENCIA 111
- Phone: 954-499-5400 111
- 2° Medida: 120
- Las picas se giran 90° con 120
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Amprobe Multitest-1000 Continuity-Tester
Urządzenia pomiarowe Amprobe Telaris-Earth-Test Earth-Resistance-Tester Instrukcja Użytkownika
(124 strony)
(124 strony)
Urządzenia pomiarowe Amprobe AT-3000 Underground-Wire-Pipe-Locator Instrukcja Użytkownika
(2 strony)
(2 strony)
Hmc-electronics 910-1 Permabond 910 Cyanoacrylate Adhesive, Genera podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Narzędzia Hmc-electronics 910-1 Permabond 910 Cyanoacrylate Adhesive, Genera.
Dostarczamy 1 pdf podręczników Hmc-electronics 910-1 Permabond 910 Cyanoacrylate Adhesive, Genera do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji